{"title":"Engine Testers","description":"\u003cp\u003eTest equipment for engine diagnostics: compression and leak-down testers, diesel compression testers, common rail high-pressure testers, cooling system, oil pressure and turbo leak test kits, timing light, vacuum pump and electronic stethoscope. Professional tools in workshop quality for independent workshops and commercial use – with German support and buy on invoice via Klarna or PayPal.\u003c\/p\u003e","products":[{"product_id":"kompressionstester-druckverlusttester-46-tlg","title":"Compression \u0026 Leak-Down Tester 46 pcs for Petrol \u0026 Diesel – in Carry Case","description":"\u003ch2\u003eCompression and leak-down tester 46 pcs – Reliably assess compression and cylinder sealing\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003eTwo tests in one set\u003c\/strong\u003e: compression test and leak-down test\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eCompression gauge 0–50 bar (0–700 psi)\u003c\/strong\u003e with rubber protective boot and release button\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eLeak-down tester with pressure regulator\u003c\/strong\u003e: inlet pressure 0–7 bar, pressure loss in percent\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eAdapters for petrol and diesel engines\u003c\/strong\u003e – spark plug, glow plug and injector holes, all in a case\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eIf an engine runs rough, is hard to start or loses power, compression is one of the first things to check. With the \u003cstrong\u003e46-piece compression and leak-down tester\u003c\/strong\u003e you first measure the compression pressure of each cylinder and then use the leak-down test to find out where the compression is being lost – at the valves, at the piston rings or at the cylinder head gasket. A professional test set in workshop quality for independent workshops and commercial use, for petrol and diesel engines.\u003c\/p\u003e\n\n\u003ch3\u003eCompression test: compare the cylinders\u003c\/h3\u003e\n\n\u003cp\u003eScrew the appropriate adapter into the spark plug, glow plug or injector hole, connect the compression gauge via the quick coupler and crank the engine with the starter motor. After each measurement, reset the reading with the release button and test the next cylinder. What matters is the comparison: if one cylinder deviates significantly from the others, a leak-down test follows.\u003c\/p\u003e\n\n\u003ch3\u003eLeak-down test: narrow down the cause\u003c\/h3\u003e\n\n\u003cp\u003eTurn the piston of the cylinder to top dead centre on the compression stroke, connect the leak-down tester to compressed air and set the inlet pressure on the regulator. The large gauge shows what percentage of the pressure the cylinder is losing. Where the air escapes reveals the cause: hissing in the intake points to the intake valve, at the exhaust to the exhaust valve, at the oil filler neck to the piston rings, and bubbles in the coolant to the cylinder head gasket.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eThe leak-down test requires compressed air from the workshop supply or a compressor, which is not included in the scope of delivery. It is connected via a plug nipple on the pressure regulator – depending on the coupling system in your workshop, a matching nipple may be required. If the piston is not exactly at top dead centre, the air pressure can turn the engine: keep hands away from belts and fan. Take the specified values for compression pressure and permissible pressure loss from the manufacturer data for the engine. Which adapter fits depends on the thread and installation situation; the gauge scales are labelled in English or in bar and psi.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eContents\u003c\/th\u003e\n\u003ctd\u003e46-piece set, compression and leak-down tester\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEngines\u003c\/th\u003e\n\u003ctd\u003ePetrol and diesel engines\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCompression gauge\u003c\/th\u003e\n\u003ctd\u003e0–50 bar \/ 0–700 psi, rubber protective boot, release button\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLeak-down tester\u003c\/th\u003e\n\u003ctd\u003ePressure regulator, inlet gauge 0–7 bar \/ 0–100 psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLeak-down gauge\u003c\/th\u003e\n\u003ctd\u003e0–100 % with coloured zones\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eConnections\u003c\/th\u003e\n\u003ctd\u003eBrass quick couplers, compressed air plug nipple on the regulator\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAdapters\u003c\/th\u003e\n\u003ctd\u003efor spark plug, glow plug and injector holes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003ePlastic case with foam insert\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– Compression tester with 0–50 bar gauge and hose\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Leak-down tester with pressure regulator and two gauges\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Connecting hoses with quick couplers\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Adapters for spark plug, glow plug and injector holes (petrol and diesel)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Holding plates for injector adapters\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Extension with knurled grip\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– PTFE sealing tape\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Plastic case with foam insert\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367240106358,"sku":"SW11320","price":119.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11320-kompressionstester-druckverlusttester-46-tlg.jpg?v=1794817512"},{"product_id":"diesel-kompressionstester-18-tlg-gluehkerze-injektor","title":"Diesel Compression Tester 18 pcs for Car \u0026 Truck – 0–70 bar, 14 Thread Adapters","description":"\u003ch2\u003eDiesel compression tester 18 pcs – Measure compression via the glow plug or injector hole\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003eGauge 0–70 bar (0–1000 psi)\u003c\/strong\u003e, Ø 80 mm, with rubber protective boot\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e8 glow plug adapters\u003c\/strong\u003e from M8 × 1 to M12 × 1.25\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e6 injector and screw-in adapters\u003c\/strong\u003e from M18 × 1.5 to M24 × 2\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eApprox. 50 cm hose\u003c\/strong\u003e with brass quick coupler, release button on the gauge\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eStarting problems, loss of power or rough idling on a diesel: the cause is often insufficient compression in individual cylinders. The \u003cstrong\u003e18-piece diesel compression tester\u003c\/strong\u003e is screwed in instead of the glow plug or injector and shows the compression pressure of each cylinder. A professional test set in workshop quality for independent workshops and commercial use – for diesel engines in cars, vans and trucks as well as in tractors and working machinery.\u003c\/p\u003e\n\n\u003ch3\u003eHow to measure\u003c\/h3\u003e\n\n\u003cp\u003eRemove the glow plug or injector of the cylinder to be tested, screw in the appropriate adapter and connect the gauge via the quick coupler. Deactivate the fuel injection, crank the engine with the starter motor and read off the maximum value. Reset the reading with the release button and test the next cylinder. What matters is the comparison: if one cylinder deviates significantly from the others, it is suspect.\u003c\/p\u003e\n\n\u003ch3\u003eAdapters for glow plug and injector holes\u003c\/h3\u003e\n\n\u003cp\u003eThe eight slim glow plug adapters cover the threads M8 × 1, M10 × 1, M10 × 1.25 and M12 × 1.25. For the injector hole, adapters with M20 × 1.5, M22 × 1.5, M24 × 1.5 and M24 × 2 are included, plus a long M18 × 1.5 screw-in adapter. The set is completed by a holding plate as well as a copper ring, rubber ring and aluminium sealing cone for sealing.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eThe tester is intended for diesel engines; spark plug adapters for petrol engines are not included. Whether an adapter fits depends on the thread, bore depth and installation situation – please compare the thread specifications beforehand. When removing and installing injectors, the specifications of the vehicle manufacturer apply; the sealing rings on the injector generally have to be replaced. Take the specified values for compression pressure from the manufacturer data for the engine.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eMeasuring range\u003c\/th\u003e\n\u003ctd\u003e0–70 bar \/ 0–1000 psi (dual scale)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGauge\u003c\/th\u003e\n\u003ctd\u003eØ 80 mm, rubber protective boot, release button\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHose\u003c\/th\u003e\n\u003ctd\u003eapprox. 50 cm, brass quick coupler\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGlow plug adapters\u003c\/th\u003e\n\u003ctd\u003e8 pcs: M8 × 1, M10 × 1 (4 ×), M10 × 1.25 (2 ×), M12 × 1.25\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInjector adapters\u003c\/th\u003e\n\u003ctd\u003e5 pcs: M20 × 1.5, M22 × 1.5 (2 ×), M24 × 1.5, M24 × 2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eScrew-in adapter\u003c\/th\u003e\n\u003ctd\u003eM18 × 1.5, long\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAccessories\u003c\/th\u003e\n\u003ctd\u003eHolding plate, copper ring Ø 14 mm, rubber ring Ø 14 mm, aluminium sealing cone Ø 12 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEngines\u003c\/th\u003e\n\u003ctd\u003eDiesel engines in cars, vans, trucks, tractors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– Compression gauge 0–70 bar with hose and brass quick coupler\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 8 glow plug adapters\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 5 injector adapters\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 1 screw-in adapter M18 × 1.5\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Holding plate\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Copper ring, rubber ring and aluminium sealing cone\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367241548150,"sku":"SW11321","price":59.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11321-diesel-kompressionstester-18-tlg.jpg?v=1794817522"},{"product_id":"common-rail-hochdrucktester-31-tlg-diesel","title":"Common Rail High-Pressure Tester 31 pcs for Diesel – Gauge up to 2,000 bar","description":"\u003ch2\u003eCommon rail high-pressure tester 31 pcs – Mechanically measure rail pressure and high-pressure pump\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003eGauge 0–2,000 bar\u003c\/strong\u003e to EN 837-1, class 1.6, with rubber protective boot\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e4 high-pressure hoses\u003c\/strong\u003e and \u003cstrong\u003e4 adapters M12 \/ M14\u003c\/strong\u003e for connection in the high-pressure circuit\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e12 blanking caps\u003c\/strong\u003e for the injector lines and \u003cstrong\u003e6 dummy regulators\u003c\/strong\u003e for shutting off\u003c\/li\u003e\n\u003cli\u003e✔ With collecting bottle, seal kit, gloves and instructions in a \u003cstrong\u003eplastic case\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eIf a common rail diesel starts poorly or not at all, or the control unit reports a rail pressure that is too low, the question arises: is it the high-pressure pump, the pressure control, a leaking injector or the rail pressure sensor? The \u003cstrong\u003ecommon rail high-pressure tester\u003c\/strong\u003e shows the actual pressure in the high-pressure circuit directly on the gauge – independently of the sensor value in the diagnostic tool. A professional test set in workshop quality for independent workshops and commercial use.\u003c\/p\u003e\n\n\u003ch3\u003eTypical tests\u003c\/h3\u003e\n\n\u003cp\u003e\u003cstrong\u003ePressure build-up when starting:\u003c\/strong\u003e Connect the gauge via a high-pressure hose and adapter and read off during cranking whether the pump builds up sufficient pressure. \u003cstrong\u003ePump delivery rate:\u003c\/strong\u003e Use the blanking caps to seal the connections of the injector lines and assess the pump pressure independently of the injectors. \u003cstrong\u003ePressure control and injectors:\u003c\/strong\u003e On suitable pumps, the flange blanking pieces replace the pressure control valve; together with selectively shutting off individual lines, this lets you narrow down whether a pressure loss originates from the pressure control or from a leaking injector. Compare the measured pressure with the specified value of the manufacturer and with the value of the rail pressure sensor in the diagnostic tool.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eVery high pressures occur in the high-pressure circuit of a common rail system. Only connect or disconnect fittings with the engine switched off and the system depressurised, wear safety goggles and gloves, and collect escaping fuel in the collecting bottle. Test procedures and specified values are vehicle-specific and must be taken from the manufacturer data; the enclosed instructions are in English. Which adapters, blanking caps and dummy regulators fit depends on the pump, rail and line thread – if in doubt, we will be happy to advise you.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eMeasuring range\u003c\/th\u003e\n\u003ctd\u003e0–2,000 bar\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGauge\u003c\/th\u003e\n\u003ctd\u003eEN 837-1, accuracy class 1.6, rubber protective boot\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTest block\u003c\/th\u003e\n\u003ctd\u003eT-piece with drain connection\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHoses\u003c\/th\u003e\n\u003ctd\u003e4 high-pressure hoses\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAdapters\u003c\/th\u003e\n\u003ctd\u003e4 pcs for M12 and M14\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBlanking caps\u003c\/th\u003e\n\u003ctd\u003e12 pcs in two sizes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDummy regulators\u003c\/th\u003e\n\u003ctd\u003e6 flange blanking pieces in different designs\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOther accessories\u003c\/th\u003e\n\u003ctd\u003e2 thread adapters, retaining clip, collecting bottle, seal kit, gloves size 10\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCase\u003c\/th\u003e\n\u003ctd\u003e44.6 × 30.7 × 11.4 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– Gauge 0–2,000 bar with test block\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 4 high-pressure hoses\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 4 adapters M12 \/ M14\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 12 blanking caps for injector lines\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 6 flange blanking pieces (dummy regulators)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 2 thread adapters\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Retaining clip\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Collecting bottle\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Bag of O-rings and seals\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Work gloves (size 10)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Operating instructions (English)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Plastic case\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367242236278,"sku":"SW11323","price":179.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11323-common-rail-hochdrucktester-31-tlg.jpg?v=1794817529"},{"product_id":"kuehlsystem-abdrueckset-28-tlg-vakuum-befueller","title":"Cooling System Pressure Test Kit 28 pcs for Cars – Pressure Test \u0026 Vacuum Fill","description":"\u003ch2\u003eCooling system pressure test kit 28 pcs – Find leaks and fill coolant without air bubbles\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003ePressure test\u003c\/strong\u003e with hand pump and gauge \u003cstrong\u003e0–2.5 bar (0–35 psi)\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e17 colour-coded adapters\u003c\/strong\u003e for expansion tanks and radiators, plus 3 metal test caps and a conical rubber adapter\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eVacuum filling unit\u003c\/strong\u003e with its own gauge: bleed the cooling system and fill it without air bubbles\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e2 adapters for pressure caps\u003c\/strong\u003e and everything to hand in a sturdy plastic case\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eCoolant loss without a visible puddle, an overheating engine or suspected leaks in hoses, radiator or water pump: with the \u003cstrong\u003e28-piece cooling system pressure test kit\u003c\/strong\u003e you pressurise the cooling system with the engine cold and see on the gauge whether it is tight. If the pressure drops, coolant escapes at the leaking point – so you find the fault instead of replacing parts on suspicion. After the repair, you fill the system without trapped air using the vacuum filling unit. A professional tool in workshop quality for independent workshops and commercial use.\u003c\/p\u003e\n\n\u003ch3\u003ePressure test: how to pressure-test the system\u003c\/h3\u003e\n\n\u003cp\u003eWith the engine cold, remove the pressure cap, fit the appropriate colour-coded adapter onto the expansion tank or radiator neck and connect the hand pump via the hose and quick coupler. Pump up to the system pressure stated on the pressure cap and watch the gauge: if the needle stays put, the system is tight. If it drops, check hoses, radiator, water pump and connections for escaping coolant; if the pressure drops without an external leak, there may be an internal loss. With the two cap adapters you can also check whether the pressure cap itself holds the pressure.\u003c\/p\u003e\n\n\u003ch3\u003eVacuum filling without air bubbles\u003c\/h3\u003e\n\n\u003cp\u003eThe filling unit is placed on the expansion tank and operated with compressed air. It creates a vacuum in the cooling system, which you read off on the gauge of the unit. The system then draws fresh coolant from the supply container through the transparent filling hose – without trapped air, so lengthy bleeding is no longer necessary. If the vacuum holds before filling, this is also an indication that the system is tight.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eOnly carry out the pressure test and filling with the engine cooled down – hot coolant is under pressure. Do not exceed the system pressure stated on the pressure cap. The vacuum filling unit requires a compressed air supply (compressor), which is not included in the scope of delivery; coolant is not included either. The adapters fit many common cars – whether a suitable adapter is included for a particular vehicle depends on the manufacturer and model.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eContents\u003c\/th\u003e\n\u003ctd\u003e28 pieces in a plastic case\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePressure test\u003c\/th\u003e\n\u003ctd\u003eHand pump with gauge, 0–2.5 bar \/ 0–35 psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAdapters\u003c\/th\u003e\n\u003ctd\u003e17 colour-coded plastic adapters, 3 metal test caps, 1 conical rubber adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCap test\u003c\/th\u003e\n\u003ctd\u003e2 adapters for pressure caps\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFilling\u003c\/th\u003e\n\u003ctd\u003eVacuum filling unit with vacuum gauge and hanging chain\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFilling unit operation\u003c\/th\u003e\n\u003ctd\u003eCompressed air (compressor, not included)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHoses\u003c\/th\u003e\n\u003ctd\u003etransparent filling hoses, blue connecting hose\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– Hand pump with gauge (0–2.5 bar), hose and quick coupler\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 17 colour-coded adapters for expansion tanks and radiators\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 3 metal test caps\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 2 adapters for pressure caps (black and light blue)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 1 conical rubber adapter\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Vacuum filling unit with vacuum gauge and hanging chain\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Transparent filling hoses and blue connecting hose\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Plastic case\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367244398966,"sku":"SW11324","price":74.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11324-kuehlsystem-abdrueckset-28-tlg.jpg?v=1794817542"},{"product_id":"oeldruck-pruefset-kfz-10-adapter","title":"Oil Pressure Test Kit for Car Engines – Gauge 0–10 bar with 10 Thread Adapters","description":"\u003ch2\u003eOil pressure test kit – Measure engine oil pressure directly at the engine\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003eGauge 0–10 bar (0–140 psi)\u003c\/strong\u003e with dual scale and side release button\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e10 steel thread adapters\u003c\/strong\u003e: R 1\/8 (DIN 2999), NPT, UNF and metric M10 to M18\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eQuick coupler\u003c\/strong\u003e on the hose – connect and disconnect the gauge in seconds\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e90° angle coupler\u003c\/strong\u003e for tight installation spaces, O-rings and case included\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eThe oil pressure warning light only signals “too low” – the \u003cstrong\u003eoil pressure test kit\u003c\/strong\u003e shows how much pressure is actually present. You screw the appropriate adapter in place of the oil pressure switch, connect the gauge and read the oil pressure at idle and at increased engine speed. This tells you whether a worn oil pump, bearing damage or just a faulty oil pressure switch is behind the warning. A professional measuring instrument in workshop quality for independent workshops and commercial use.\u003c\/p\u003e\n\n\u003ch3\u003eHow to measure\u003c\/h3\u003e\n\n\u003cp\u003eUnscrew the oil pressure switch or oil pressure sender, screw in the adapter with the matching thread and O-ring, and attach the quick coupler of the gauge hose. If space on the engine is tight, fit the 90° angle coupler in between. Start the engine, bring it up to operating temperature and compare the oil pressure at idle and at increased engine speed with the specifications of the vehicle manufacturer. Before disconnecting, release the residual pressure via the side release button on the gauge.\u003c\/p\u003e\n\n\u003ch3\u003eThe adapters at a glance\u003c\/h3\u003e\n\n\u003cp\u003eThe ten steel adapters are numbered 1 to 10: R 1\/8 (DIN 2999), 1\/8″ × 27 NPT, 1\/4″ × 18 NPT, 3\/8″ × 20 UNF, 1\/2″ × 20 UNF as well as M10, M12, M14, M16 and M18. All have the same plug nipple for the quick coupler on the hose.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eThe manufacturer designates the kit as an oil pressure tester. It is not intended for fuel systems: there is no adapter for Schrader test valves, and high-pressure systems such as common rail or petrol direct injection are far above the 10 bar measuring range. The manufacturer does not state the thread pitches of the metric adapters – please compare them with the thread of the oil pressure switch beforehand.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eMeasuring range\u003c\/th\u003e\n\u003ctd\u003e0–10 bar \/ 0–140 psi (dual scale)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGauge\u003c\/th\u003e\n\u003ctd\u003ewith side pressure release button\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eConnection\u003c\/th\u003e\n\u003ctd\u003eHose with brass quick coupler\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAdapters\u003c\/th\u003e\n\u003ctd\u003e10 × steel, numbered 1–10\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThreads\u003c\/th\u003e\n\u003ctd\u003eR 1\/8 (DIN 2999), 1\/8″ × 27 NPT, 1\/4″ × 18 NPT, 3\/8″ × 20 UNF, 1\/2″ × 20 UNF, M10, M12, M14, M16, M18\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAccessories\u003c\/th\u003e\n\u003ctd\u003e90° angle quick coupler, O-rings\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003ePlastic case\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– Gauge 0–10 bar with hose and quick coupler\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 10 steel thread adapters (no. 1 to 10)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 90° angle quick coupler\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Set of O-rings\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Plastic case\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367247085942,"sku":"SW11325","price":59.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11325-oeldruck-pruefset-0-10-bar.jpg?v=1794817551"},{"product_id":"turbolader-lecktester-ladeluft-9-tlg","title":"Turbo Leak Tester 9 pcs for Charge Air Systems – Adapters 35–90 mm, Regulator","description":"\u003ch2\u003eTurbo leak tester 9 pcs – Find leaks in the charge air system\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003eStepped adapters for hoses from 35 to 90 mm\u003c\/strong\u003e – 12 diameters in 5 mm steps\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e4 test adapters with connection nipple and 4 blanking plugs\u003c\/strong\u003e – one matching pair per size range\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eInflator unit with pressure regulator, gauge and ball valve\u003c\/strong\u003e for fine adjustment of the test pressure\u003c\/li\u003e\n\u003cli\u003e✔ For \u003cstrong\u003eintercoolers, charge air hoses and pipes\u003c\/strong\u003e on turbocharged engines, all in a plastic case\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eLoss of power, whistling noises or a fault code relating to boost pressure: the cause is often a leak in the charge air system – a torn hose, a loose clamp or a leaking intercooler. With the \u003cstrong\u003e9-piece turbo leak tester\u003c\/strong\u003e you seal the charge air tract at both ends, pressurise it with compressed air with the engine stopped and find the leak instead of replacing parts on suspicion. A professional tool in workshop quality for independent workshops and commercial use.\u003c\/p\u003e\n\n\u003ch3\u003eHow to test\u003c\/h3\u003e\n\n\u003cp\u003eDisconnect the charge air tract at both ends, for example at the turbocharger and at the throttle valve. Insert the test adapter with nipple into one hose end and the blanking plug from the same size range into the other, and secure both with the hose clamps. Connect the inflator unit to compressed air, connect it to the nipple with the test hose and slowly increase the pressure on the regulator, starting from a low value. You can hear leaks by the hissing or make them visible with leak detection spray or soapy water; if the pressure on the gauge remains stable, the tract is tight.\u003c\/p\u003e\n\n\u003ch3\u003eThe adapters at a glance\u003c\/h3\u003e\n\n\u003cp\u003eThe eight stepped adapters form four pairs of test adapter and blanking plug. Each pair covers three hose diameters: 35\/40\/45 mm, 50\/55\/60 mm, 65\/70\/75 mm and 80\/85\/90 mm.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eCompressed air (compressor) is required for operation and is not included in the scope of delivery. The compressed air connection on the ball valve has a female thread – a plug nipple to match your compressed air coupling is not included. Only test with the engine stopped and at low pressure, at most up to the boost pressure specified by the vehicle manufacturer. According to the manufacturer, the gauge measures 0 to 5 bar (0 to 70 psi).\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eContents\u003c\/th\u003e\n\u003ctd\u003e9 pieces in a plastic case\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHose diameter\u003c\/th\u003e\n\u003ctd\u003e35 to 90 mm in 5 mm steps (12 sizes)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAdapters\u003c\/th\u003e\n\u003ctd\u003e4 test adapters with connection nipple, 4 blanking plugs, each stepped\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSize ranges\u003c\/th\u003e\n\u003ctd\u003e35–45 \/ 50–60 \/ 65–75 \/ 80–90 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInflator unit\u003c\/th\u003e\n\u003ctd\u003ePressure regulator with rotary knob, gauge (bar\/psi), ball valve, test hose with coupling\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGauge\u003c\/th\u003e\n\u003ctd\u003e0–5 bar \/ 0–70 psi (manufacturer specification)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCompressed air connection\u003c\/th\u003e\n\u003ctd\u003eFemale thread on the ball valve\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– Inflator unit with pressure regulator, gauge, ball valve and test hose\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 4 stepped test adapters with connection nipple\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 4 stepped blanking plugs\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Plastic case\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367248265590,"sku":"SW11326","price":69.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11326-turbolader-lecktester-9-tlg.jpg?v=1794817559"},{"product_id":"digitale-zuendlichtpistole-induktiv-12-v","title":"Digital Timing Light for Petrol Engines – Inductive, RPM \u0026 Ignition Advance","description":"\u003ch2\u003eDigital timing light – Make the ignition timing of petrol engines visible\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003eInductive pickup\u003c\/strong\u003e: the clamp is placed around the ignition lead of cylinder 1 – nothing has to be cut open\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003e4-digit digital display\u003c\/strong\u003e, switchable between engine speed and ignition advance with the R\/A button\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eAdjustable advance\u003c\/strong\u003e via the + and − buttons, four-stroke \/ two-stroke selection with 4\/2\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003ePowered by the 12 V battery\u003c\/strong\u003e with red and black crocodile clips\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWith the \u003cstrong\u003edigital timing light\u003c\/strong\u003e you check the ignition timing of petrol engines directly on the running engine. The light flashes in time with the ignition of cylinder 1: point it at the timing marks on the pulley or flywheel and they appear to stand still – so you can see immediately whether the ignition timing is correct. The digital display also shows engine speed and ignition advance. A test instrument in workshop quality for independent workshops, classic car and motorcycle workshops and commercial use.\u003c\/p\u003e\n\n\u003ch3\u003eHow to check the ignition timing\u003c\/h3\u003e\n\n\u003cp\u003eBring the engine up to operating temperature and switch it off. Connect the red clip to the positive terminal and the black clip to the negative terminal of the 12 V battery and place the red inductive clamp around the ignition lead of cylinder 1. Let the engine idle and point the light at the marks. Use + and − to shift the flash timing until the timing mark lines up with the reference mark – the display then shows the ignition advance. When you increase the engine speed, you can also see whether the ignition advance is working.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eThe timing light is designed for petrol engines with a 12 V electrical system, not for diesel engines. The inductive clamp needs an accessible ignition lead: if the ignition coils sit directly on the spark plugs, a direct connection is not possible. The test requires timing marks on the pulley or flywheel; on many modern engines the control unit regulates the ignition timing – it can then be checked but not adjusted mechanically. On a running engine, watch out for the fan, belts and hot parts.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eDigital timing light (stroboscope) with inductive pickup\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDisplay\u003c\/th\u003e\n\u003ctd\u003e4-digit LED digital display with indicator lights\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eButtons\u003c\/th\u003e\n\u003ctd\u003eR\/A (engine speed \/ ignition advance), + and − (advance adjustment), 4\/2 (four-stroke \/ two-stroke)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEngines\u003c\/th\u003e\n\u003ctd\u003ePetrol engines, four-stroke and two-stroke\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003e12 V vehicle battery via crocodile clips red (+) and black (−)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSignal pickup\u003c\/th\u003e\n\u003ctd\u003eInductive clamp on the ignition lead of cylinder 1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHousing\u003c\/th\u003e\n\u003ctd\u003eABS plastic, rubber frame around the display\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003eapprox. 29 × 18 cm, handle approx. 9 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– Digital timing light with permanently attached cable set\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Battery clips red (+) and black (−)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Red inductive clamp for the ignition lead\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367250461046,"sku":"SW11327","price":54.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11327-digitale-zuendlichtpistole.jpg?v=1794817570"},{"product_id":"handvakuumpumpe-mit-manometer-bremsenentlueftung","title":"Hand Vacuum Pump with Gauge for Cars – Vacuum Testing \u0026 Brake Bleeding","description":"\u003ch2\u003eHand vacuum pump with gauge – Test vacuum and bleed brakes\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003eGenerate vacuum and pressure\u003c\/strong\u003e – switchable via the ring on the pump head\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eGauge\u003c\/strong\u003e with scales in bar, inHg and psi: displays down to −1 bar vacuum and up to 3 bar pressure\u003c\/li\u003e\n\u003cli\u003e✔ Test \u003cstrong\u003evacuum actuators, EGR valves and wastegate actuators\u003c\/strong\u003e as well as vacuum lines precisely\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eBrake and clutch bleeding\u003c\/strong\u003e with two 120 ml collection containers, 12 adapters and hoses in a case\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eThe \u003cstrong\u003ehand vacuum pump with gauge\u003c\/strong\u003e is a versatile test tool for independent workshops and commercial use. Using the hand lever, you generate vacuum in a controlled way and read on the gauge whether a component responds and whether it holds the vacuum. This lets you test vacuum units and actuators, for example on the EGR valve, wastegate or intake manifold flaps, and check vacuum lines for leaks – without the engine running. At the same time, the set is a complete brake bleeding kit: with a collection container and adapters, you can bleed brakes and hydraulic clutches on your own. Workshop quality in a sturdy case.\u003c\/p\u003e\n\n\u003ch3\u003eTesting vacuum actuators, EGR and wastegate\u003c\/h3\u003e\n\n\u003cp\u003eConnect the hose to the vacuum port of the actuator using a suitable adapter and slowly pump up the vacuum. If the linkage moves and the gauge needle stays put, the actuator is in order. If the value drops, the diaphragm or line is leaking. Use the black ring on the pump head to switch between suction (vacuum) and pressure (positive pressure).\u003c\/p\u003e\n\n\u003ch3\u003eBleeding brakes and clutch\u003c\/h3\u003e\n\n\u003cp\u003eFor bleeding, a collection container is placed between the pump and the bleed valve: the side of the lid marked “TO PUMP” is connected to the pump, the other side to the bleed valve via hose and adapter. Using vacuum, you draw brake fluid and air into the container – without a second person on the brake pedal. Each of the two containers holds 120 ml.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eThe gauge displays vacuum down to −1 bar; with the hand pump, around 20 inHg (approx. −0.68 bar) can be reached in normal operation. The set is not intended for extracting or transferring fuel. Always connect the container lid with the “TO PUMP” side towards the pump so that no fluid enters the pump; brake fluid attacks paintwork and must be disposed of properly. On vehicles with ABS\/ESP, an additional bleeding routine using a diagnostic tool may be necessary depending on the manufacturer. Labelling and instructions are in English.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eHand vacuum and pressure pump with gauge\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFunction\u003c\/th\u003e\n\u003ctd\u003eVacuum and pressure, switchable on the pump head\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGauge\u003c\/th\u003e\n\u003ctd\u003eScales in bar, inHg and psi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVacuum display range\u003c\/th\u003e\n\u003ctd\u003e0 to −1 bar\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePressure display range\u003c\/th\u003e\n\u003ctd\u003e0 to 3 bar (0 to 40 psi)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAchievable vacuum\u003c\/th\u003e\n\u003ctd\u003eapprox. 20 inHg (around −0.68 bar) in normal operation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePump body\u003c\/th\u003e\n\u003ctd\u003eAluminium, rubberised grips\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCollection containers\u003c\/th\u003e\n\u003ctd\u003e2 × 120 ml, lid with sealing ring\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAdapters\u003c\/th\u003e\n\u003ctd\u003e12 pcs, conical, angled and straight\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStorage\u003c\/th\u003e\n\u003ctd\u003ePlastic case with moulded insert\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– Hand vacuum pump with gauge\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 2 collection containers of 120 ml each with lids\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 12 adapters (conical, angled and straight)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 1 long hose and 3 short hose sections\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 1 suction cup\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Plastic case\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Operating instructions (English)\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367252853110,"sku":"SW11328","price":59.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11328-handvakuumpumpe-mit-manometer.jpg?v=1794817581"},{"product_id":"elektronisches-stethoskop-6-kanal-kfz","title":"6-Channel Electronic Stethoscope for Cars – Locate Chassis \u0026 Engine Noises","description":"\u003ch2\u003e6-channel electronic stethoscope – Find sources of noise on the chassis, gearbox and engine\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e✔ \u003cstrong\u003e6 clamp sensors\u003c\/strong\u003e with crocodile clips – connect six measuring points at the same time\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eChannel selector 1 to 6\u003c\/strong\u003e with volume control: switch between the measuring points with the rotary knob\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003eAdditional single-channel mode\u003c\/strong\u003e with 140 mm probe tip for targeted searching on the running engine\u003c\/li\u003e\n\u003cli\u003e✔ \u003cstrong\u003ePiezo sensors\u003c\/strong\u003e with 800 mV\/g sensitivity, headphones and case included\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eRattling, knocking, grinding or humming that only occurs while driving is often hard to find in the workshop. With the \u003cstrong\u003e6-channel electronic stethoscope\u003c\/strong\u003e you attach up to six clamp sensors to suspect components – for example on control arms, anti-roll bars, suspension struts, brake calipers or the gearbox – and listen to each measuring point in turn via the headphones during the test drive. Where the noise is loudest, that is where the cause lies. A diagnostic tool in workshop quality for independent workshops and commercial use.\u003c\/p\u003e\n\n\u003ch3\u003eSix measuring points during the test drive\u003c\/h3\u003e\n\n\u003cp\u003eThe sensors are attached to the components with the crocodile clips, and the cables are secured with the supplied hook-and-loop straps and routed to the channel selector. Use the rotary knob to select measuring point 1 to 6 and the knurled wheel to adjust the volume. Colour-marked cables and coloured channel fields make assignment easier. The test drive should be carried out by two people: one drives, the other listens.\u003c\/p\u003e\n\n\u003ch3\u003eSingle-channel mode on the running engine\u003c\/h3\u003e\n\n\u003cp\u003eFor targeted searching in the engine compartment, fit the probe tip onto the amplifier handset and connect the headphones. This lets you listen to the valve train, injectors, bearings, alternator, water pump or tensioner pulleys, electronically amplified and with adjustable volume.\u003c\/p\u003e\n\n\u003ch3\u003ePlease note\u003c\/h3\u003e\n\n\u003cp\u003eThe stethoscope does not display measured values but makes structure-borne sound audible – assessing the noises requires experience. Attach sensors and cables so that they cannot come into contact with rotating parts, brake discs or the hot exhaust system, and only carry out the test drive on a suitable route. The channel selector and single-channel amplifier run on 9 V block batteries (6F22). The labelling on the device is in English.\u003c\/p\u003e\n\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\n\u003ctable border=\"1\" cellpadding=\"8\" cellspacing=\"0\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eElectronic stethoscope for 6-channel and single-channel operation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSensor type\u003c\/th\u003e\n\u003ctd\u003ePiezoelectric accelerometer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSensitivity\u003c\/th\u003e\n\u003ctd\u003emax. 800 mV\/g\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSignal ratio\u003c\/th\u003e\n\u003ctd\u003e60 to 120 dB\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eResonant frequency\u003c\/th\u003e\n\u003ctd\u003e24 kHz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMeasuring points\u003c\/th\u003e\n\u003ctd\u003e6 clamp sensors with crocodile clips, channel selection via rotary switch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProbe tip\u003c\/th\u003e\n\u003ctd\u003e140 mm (single-channel mode)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003e9 V block battery (6F22), power consumption below 15 mW\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCase\u003c\/th\u003e\n\u003ctd\u003eapprox. 41 × 35 × 11 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eScope of delivery\u003c\/h3\u003e\n\n\u003cp style=\"margin:0 0 2px;\"\u003e– 6-channel selector with volume control\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 6 clamp sensors with crocodile clips and colour-marked cables\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Single-channel amplifier (handset) with volume control\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Probe tip for the single-channel amplifier\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Headphones\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 2 × 9 V block battery (6F22)\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– 7 hook-and-loop straps for securing the cables\u003c\/p\u003e\n\u003cp style=\"margin:0 0 2px;\"\u003e– Plastic case\u003c\/p\u003e\n\n\u003cp\u003eBuy on invoice available (Klarna or PayPal). Professional tool in workshop quality for independent workshops and commercial use – if you have any questions about using it, we will be happy to advise you by phone.\u003c\/p\u003e","brand":"auto-diagnostik","offers":[{"title":"Default Title","offer_id":59367255638390,"sku":"SW11329","price":119.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0855\/8723\/1025\/files\/sw11329-elektronisches-stethoskop-6-kanal.jpg?v=1794817590"}],"url":"https:\/\/auto-diagnostik.de\/en\/collections\/motor-pruefgeraete.oembed","provider":"auto-diagnostik","version":"1.0","type":"link"}